6 & 8 INCH CHIPPERSOWNER'S MANUALManual PN 13987-00Rev. 0204 Companion to 13988-00MODELS748247262071620
Page 86" & 8" Bear Cat Chipper Operator’s Manual2.2 ATTACH THE CHIPPER CHUTEHydraulicFeedChipperChuteFigure 2.2 - Chipper Chute Assembly
Page 96" & 8" Bear Cat Chipper Operator’s Manual2.5 CONNECT THE CONTROL CABLE2.6 ADJUSTING THE HYDRAULICFEED CONTROL CABLEFigure 2.5 - C
Page 106" & 8" Bear Cat Chipper Operator’s ManualTo avoid sparks and a possible explosion or fire due to ashort circuit:1. Do not touch
Page 116" & 8" Bear Cat Chipper Operator’s ManualFor engine controls and maintenance please refer to theengine owner's manual inclu
Page 126" & 8" Bear Cat Chipper Operator’s Manual1. Before starting, fill engine with oil to the correct level.(see engine manual for op
Page 136" & 8" Bear Cat Chipper Operator’s Manual4.4 CHIPPINGWARNINGKeep face and body away from the feed opening. Do notoverreach. Kee
Page 146" & 8" Bear Cat Chipper Operator’s Manual1. Start the chipper engine. Bring the chipper up to operat-ing speed (see section 4.1)
Page 156" & 8" Bear Cat Chipper Operator’s Manual5.2 SHARPENING CHIPPER BLADESWhen the chipper blades dull, chipping becomes difficult.
Page 166" & 8" Bear Cat Chipper Operator’s ManualThe chipping blades should clear the chipper block locateddirectly under the chipper ch
Page 176" & 8" Bear Cat Chipper Operator’s Manual5.7 CLEARING A PLUGGED ROTORFeeding too large or too much chipable material at oncemay
DEAR BEAR CAT CUSTOMER,Thank you for purchasing a Crary Bear Cat product. The Bear Cat line is designed,tested, and manufactured to give years of depe
Page 186" & 8" Bear Cat Chipper Operator’s ManualNOTEPolyuria and lithium based greases are not compatible.Mixing the two grease types m
Page 196" & 8" Bear Cat Chipper Operator’s Manual5.9 GREASEABLE BEARINGS AND PIVOTS (CON'T)Figure 5.7 - Discharge Tube.10 to .18 oz
Page 206" & 8" Bear Cat Chipper Operator’s ManualSERVICE & MAINTENANCE5.9 GREASEABLE BEARINGS AND PIVOTS (CON'T)Figure 5.9 - Fe
Page 216" & 8" Bear Cat Chipper Operator’s ManualFollow this start-up procedure when starting a new installationor when restarting an in
Page 226" & 8" Bear Cat Chipper Operator’s ManualThe hydraulic pump normally does not require regular fluidchanges. The system filter sh
Page 236" & 8" Bear Cat Chipper Operator’s Manual6.1 GENERAL TROUBLESHOOTINGProblem Probable Cause Suggested RemediesObstructed discharg
Page 246" & 8" Bear Cat Chipper Operator’s Manual6.2 HYDROSTATIC PUMP TROUBLESHOOTING (72620 & 74824)Symptom Probable Cause Suggeste
Page 256" & 8" Bear Cat Chipper Operator’s Manual7.1 SPECIFICATIONSSpecifications are subject to change due to designmodifications.Speci
Page 266" & 8" Bear Cat Chipper Operator’s Manual7.2 BOLT TORQUECHECKING BOLT TORQUE:The table shown below is for reference purposes onl
Page 276" & 8" Bear Cat Chipper Operator’s ManualManual Improvement ProgramIf you have a suggestion on how to improve this manual, send
Page 16" & 8" Bear Cat Chipper Operator’s ManualLimited WarrantyCrary Bear Cat chippers are warranted for 1 year from date of sale for c
Manufactured in theUnited States of Americaby Crary CompanyCrary CompanyA Division of TerraMarc Industries237 12th St. NW • P.O. Box 849West Fargo,
Page 26" & 8" Bear Cat Chipper Operator’s ManualContentsSERIAL NUMBER LOCATION ...
Page 36" & 8" Bear Cat Chipper Operator’s ManualREPLACEMENT PARTSOnly genuine Bear Cat replacement parts should be used to repair the ma
Page 46" & 8" Bear Cat Chipper Operator’s Manual1.1 THE SAFETY ALERT SYMBOLThis is the safety alert symbol. It is used in this Owner /O
Page 56" & 8" Bear Cat Chipper Operator’s Manual8. If needed, always use an approved fuel container. Keepopen flames, sparks, smoking m
Page 66" & 8" Bear Cat Chipper Operator’s Manual1.4 MAINTENANCE AND STORAGESAFETYNOTEAlways read and follow the engine owner's manu
Page 76" & 8" Bear Cat Chipper Operator’s ManualYour chipper may arrive totally or partially assembled. If yourchipper arrives partially
Comments to this Manuals