ChipperOwners ManualCrary CompanyBox 849West Fargo, ND 58078(701) 282-5520 • (800) 247-7335FAX: (701) 282-9522Manufactured in theUnited States of Amer
7Figure 1Engine Model Assembly-Cont.Fill the engine with oil (per instructions in supplied engine manual) and fill the fuel tankwith fuel.Before Using
8Blower Discharge TubeMounting ClampMounting FlangeFigure 2Figure 3Engine Model Assembly-Cont.
91. Connect the PTO shaft female end to the rotor shaft using key stock and two setscrews contained in the owners kit.2. Connect the opposite end of t
10NOTE: Normal engine output is 3600 RPM no load.1. Before starting be sure to check engine oil level.2. Turn engine fuel valve to the ON position, an
111. Place tractor transmission in neutral and set parking brake.2 Connect 3 pt. mounts between the chipper and the tractor. Secure connections withs
12• Alternate greener material with dry material to lubricate the chipping blades forlonger life and better performance.• When the chipping blades be
13Check the engine oil, and change the oil and filter as recommended in the manual.Service and replace the air cleaner as recommended.The chipper blad
14To adjust:1. Lift rotor access cover and expose rotor. Loosen the two 1/2 inch boltsthat hold the chipper anvil to the frame (see figure 5).2. Meas
15Blades are sharp; avoid contact withchipper blades.Check the condition of the drive belt annually or after every 25 hours of operation,whichever com
164. Remove drive belt from pulleys.5. Install new belt on pulleys and lower belt idler. Check alignment of pulleys andadjust if needed.6. Check belt
PHONEHow to ContactBear CatM-F, 8 a.m. to 5 p.m.Central TimeCrary Bear Cat237 NW 12th StreetPO Box 849West Fargo, ND 58078Serial Number Decal Location
179. Replace roll pin with a new 1/2 x 2" pin, P/N 15137.10. Return the complete rotor assembly to the chipper frame with an overhead hoist orlif
18Service and Maintenance ScheduleBeforeEachUseEvery10HoursEvery25HoursEvery50HoursEvery100HoursEvery200HoursEvery300HoursEvery800HoursEvery1yearsInte
19TroubleshootingSuggestedRemediesa) Use branch orsimilar object toclear dischargeb) Clear rotora) Use branch orsimilar object toclear dischargeb) Sha
20SpecificationsOverall Size: 72" x 54" x 84"Max Chipper Capacity (dia.): 4"Chipper Blade Qty.: 4 Reversible Tool SteelRotor Size:
Declaration of Conformity The undersigned manufacturer: Crary Industries, Inc. 237 NW 12th Street P.O. Box 849 West Fargo, ND 58078-0849 Declares
Declaration of Conformity The undersigned manufacturer: Crary Industries, Inc. 237 NW 12th Street P.O. Box 849 West Fargo, ND 58078-0849 Declares
Box 849West Fargo, ND 58078(701) 282-5520 • (800) 247-7335FAX: (701) 282-9522www.crary.comHEALTH WARNINGGASOLINE, DIESEL, ANDOTHER PETROLEUM PRODUCTSH
WarrantyCrary Bear Cat Chipper models 73413, 73420, and 73454 are warranted for twoyears from date of sale for consumers and 90 days from the date of
1Safety Instructions ...2Engine Model Assembly ...
2Safety Instructions• Do not operate this equipment before reading and understanding the ownersmanual. See engine owners manual for additional safety
3Setting up your chipping site so you are not endangered by traffic and the public is notendangered by your work is critical for safety. Take great ca
4• Rotate the discharge tube to face the opposite direction of the towing vehicle beforetowing. This prevents the discharge tube from projecting over
5See engine ownersmanual or contactthe enginemanufacturer forengine safety andinstruction decals.Maintenance and StorageSafety Instructions-Cont.• Dis
6Your chipper may arrive totally or partially assembled. Perform the steps in this sectionif your chipper arrives partially assembled.1. Remove the c
Comments to this Manuals