He d g e Cl i p p e rOp e r a t O r 's Ma n u a l1 WARNINGRead rules for safe operation and instructions carefully. ECHO provides an Operator&
10f r o n t h a n d l e NOTE Label shows minimum spacing for front handle location.1. Position front handle in comfortable operating position and t
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l11Mixing Instructions 1. Fill an approved fuel container with half of the required amount of g
12 s t a r t I n G c o l d e n G I n e WARNINGHedge Clipper blades are very sharp. Touching them may lead to severe personal injury. Avoid touchi
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l13 WARNINGThe blades must not move at idle, otherwise serious personal in-jury may result. Per
14s t o p p I n G e n G I n e1. Throttle Release throttle and allow engine to return to idle before shutting off engine.2. Stop Switch Move stop
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l15m a I n t e n a n c e I n t e r v a l s WARNINGMoving parts can amputate ngers or cause sev
16a I r f I l t e rLevel 1.Tools required: 25 - 50 mm (1 - 2 in.) Cleaning BrushParts required: REPOWERTM AIR & FUEL FILTER KIT.1. Close ch
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l17s p a r K p l u GLevel 2.Tools Required: T-Wrench, feeler gauge, soft metal brushParts Requ
18IMPORTANT DO NOT use a metal scraper to remove dirt from the cylinder ns.4. Remove ignition wires from clip for cleaning.5. Use brush to remove
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l19Exhaust Port CleaningLevel 2.Tools required: Torx T27 L-Wrench, Wood or plastic scraperPar
2Copyright© 2008 By Echo, IncorporatedAll Rights Reserved.In t r o d u c t I o nWelcome to the ECHO family. This ECHO product was designed and manufa
20c a r b u r e t o r a d j u s t m e n tEngine Break-InNew engines must be operated a minimum duration of two tanks of fuel break-in before carburet
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l21l u b r I c a t I o nBlades Level 1.Tools Required: Clean rag, cleaning brush, oil canPar
22Drive Shaft Assembly Level 1.NOTE Hedge Clipper drive shaft should be greased every 25 hours of operation.Tools required: Torx T27 L-Wrench, scr
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l231. Disconnect spark plug wire from spark plug.2. Slide blades to allow le clearance using
24 DANGERFuel vapors are extremely ammable and may cause re and/or explosion. Never test for ignition spark by ground-ing spark plug near cylinder
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l25IMPORTANTAlways store and transport hedge clippers in a stable, horizontal position. Support
26sp e c I f I c a t I o n sMODEL ---------------------------------------------------- SHC-225, SHC-225SLength (SHC-225) ---------------------------
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l27n o t e s
CONSUMER PRODUCTSUPPORT1-800-673-15588:30 - 4:30 Mon - Fri C.S.T.ECHO, INCORPORATED400 OA k W O O D RO A DLA k E ZU R I C H , IL 60047www.echo-usa.
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l3I n t e r n a t I o n a l s y m b o l sSymbol description/applicationSymbol form/shapeSymbol
4Physical ConditionYour judgment and physical dexterity may not be good: • if you are tired or sick, •
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l5 DANGERDo not operate this product indoors or in inadequately ventilated areas. Engine exh
6Emission Control Label (located on Engine) (EXAMPLE ONLY, information on label varies by FAMILY).e q u I p m e n t WARNINGUse only ECHO approved
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l7de s c r I p t I o nLocate these safety decals on your unit. Make sure the decals are legible
8 1. POWER HEAD - Includes the Engine, Clutch, Fuel System, Ignition System and Recoil Starter. 2. THROTTLE HANDLE - FOR RIGHT HAND - Contains St
He d g e Cl i p p e rOp e r a t O r 's Ma n u a l9co n t e n t sThe ECHO product you have purchased has been factory pre-assembled for your conv
Comments to this Manuals