Echo 74624S Owners Manual v.1 User Manual

Manual P/N 14688-00Rev. 08/03Companion to P/N 14689-00Crary CompanyA Division of TerraMarc Industries237 12th St. NW • P.O. Box 849West Fargo, ND

Page 4 6” Chipper Operator’s Manual1.8 SAFETY DECAL LOCATIONSFamiliarize yourself with all of the safety and operational decals on the machine and the

Page 56” Chipper Pro Operator’s ManualSection2 AssemblyYour Chipper may arrive totally or partially assembled. Ifyour machine arrives partially assem

Page 6 6” Chipper Operator’s ManualAssembly2.3 ADDING COOLANT(DIESEL ONLY)You may need to add coolant before you start the dieselengine. While operati

Page 76” Chipper Pro Operator’s Manual2.4 BOLT TORQUECHECKING BOLT TORQUE:The table shown below is for reference purposes only and its use by anyone i

Page 8 6” Chipper Operator’s ManualAssembly2.5 ATTACH THE TRAILER WHEELS1. Remove the chipper from its shipping crate. Place theunit on a level surfac

Page 96” Chipper Pro Operator’s ManualAssembly2.8 INSTALLING THE REAR STABI-LIZERInstall the rear stabilizer by sliding the stabilizer into thecorresp

Page 10 6” Chipper Operator’s ManualDESCRIPTION OF OPERATIONThe chipper pulls in wood with the feed roller, chips the wood, and blows the chips out th

Page 116” Chipper Pro Operator’s ManualFeatures & Controls3.1 USE OF CONTROLSFig. #15 Gasoline controlsFig. #14 Diesel controlsFig. #16 Engagement

Page 12 6” Chipper Operator’s ManualSection4 OperationAs with any other piece of outdoorpower equipment, getting the “feel” forhow your machine opera

Page 136” Chipper Pro Operator’s ManualFILLING THE FUEL TANKGasoline Type:For best results use only clean, fresh, unleaded gasolinewith a pump sticker

PHONEHow to ContactBear CatM-F, 8 a.m. to 5p.m. Central TimeCrary Bear Cat237 NW 12th StreetPO Box 849West Fargo, ND 58078800-247-7335701-282-5520Fax:

Page 14 6” Chipper Operator’s Manual2. The controller also has a “try again” feature. The control-ler monitors the hydraulic pressure of the feed roll

Page 156” Chipper Pro Operator’s ManualOperation3. The controller will also flash service alerts when started.Every 15 hours it will flash (error ligh

Page 16 6” Chipper Operator’s Manual4.6 DIRECTING CHIPPER CHUTEOperationFig. #19 Directing the chuteThe chipper chute can lock into 44 different posit

Page 176” Chipper Pro Operator’s ManualOperation4.9 SAFETY BAR OPERATION4.9.1 Resetting the ChipperThe safety bar located around the chute area will s

Page 18 6” Chipper Operator’s ManualSection5 Service & Maintenance5.1 MAINTENANCE SCHEDULECheck the following items listed in the service and mai

Page 196” Chipper Pro Operator’s Manual5.2 REMOVING AND SHARPENINGTHE CHIPPER BLADESTo remove the chipping blades for sharpening:1. Remove the two 3/8

Page 20 6” Chipper Operator’s Manual5.3 REPLACING THE CHIPPERDRIVE BELTService & MaintenanceFig. # 28 Removing the beltCheck the condition of the

Page 216” Chipper Pro Operator’s Manual5.4 REPLACING THE HYDRAULICDRIVE BELT (HONDA ONLY)Check the condition of the hydraulic drive belt annually, ora

Page 22 6” Chipper Operator’s ManualService & Maintenance5.5 GREASINGGrease zerks on the Bear Cat 6” Chipper every 25 hours,depending upon conditi

Page 236” Chipper Pro Operator’s Manual5.8 CHECKING COOLANT (DIESEL)5.7 AIR FILTER (DIESEL SHOWN)5.6 ADJUSTING CHIPPER ANVILThe four chipping blades s

To prevent personal injury or property damage: Shutoff engine, disconnect spark plug wire (if applicable),make sure that all moving parts have come

Page 24 6” Chipper Operator’s ManualService & Maintenance5.9 HYD RESERVOIR FLUID5.10 HYD OIL FILTERThe chippers are tested before shipping. In ord

Page 256” Chipper Pro Operator’s Manual5.12 TROUBLESHOOTINGBefore performing any of the correction in this troubleshooting chart, refer to the appropr

Page 26 6” Chipper Operator’s Manual

Page 276” Chipper Pro Operator’s Manual

Page 28 6” Chipper Operator’s ManualManual Improvement ProgramIf you have a suggestion on how to improve this manual, send it to us. Participants whos

NOTES

Manufactured in theUnited States of Americaby Crary CompanyCrary CompanyA Division of TerraMarc Industries237 12th St. NW • P.O. Box 849West Fargo,

Section Description Page6" Chipper Operator’s ManualIIContents SAFETY ...

NOTES

6" Chipper Operator’s ManualCrary CompanyA Division of TerraMarc Industries237 12th St. NW • P.O. Box 849West Fargo, ND 58078-0849(701)282-5520

Page 16” Chipper Pro Operator’s Manual1.1 THE SAFETY ALERT SYMBOLThis manual and your machine uses this symbol to alert you of potential hazards.When

Page 2 6” Chipper Operator’s ManualSafety1.3 BEFORE OPERATING1.4 OPERATION SAFETY1. Do not allow hands, or any part ofbody or clothing, inside the fee

Page 36” Chipper Pro Operator’s Manual1.7 MAINTENANCE AND STORAGE SAFETY1. Shut off machine, remove key, anddisconnect the spark plug wire whenservici