OWNER'S MANUAL8 INCH TURNTABLE CHIPPERCH8993H - 993cc BRIGGS & STRATTONPN: 18280-00Rev. 010113 Companion to 18281-00VIN Range: 5VJAA0000DW000
6 8 INCH TURNTABLE CHIPPERSectionASSEMBLY1. Mount tires and rims to the axle using the lug nuts.2. Attach the fender supports to the trailer using t
78 INCH TURNTABLE CHIPPERENGLISH ASSEMBLY2.3 REAR STABILIZERVerify that the rear stabilizer is installed. To install the rear stabilizer,
8 8 INCH TURNTABLE CHIPPERASSEMBLY2.6 ATTACH DISCHARGE TUBEKeep nuts as tight as possible while allowing the discharge tube to freely turn.NO
98 INCH TURNTABLE CHIPPERENGLISH ASSEMBLYGasoline and diesel fuels are highly ammable and their vapors are explosive. To prevent personal injury or p
10 8 INCH TURNTABLE CHIPPERSectionFEATURES & CONTROLSUnderstanding how your machine works will help you achieve the best results when using your c
118 INCH TURNTABLE CHIPPERENGLISH FEATURES & CONTROLSThis controls the speed of the engine. Increase the throttle by moving the switch to the FAS
12 8 INCH TURNTABLE CHIPPERSectionOPERATIONAs with any other piece of outdoor power equipment, get-ting the feel for how your machine operates and get
138 INCH TURNTABLE CHIPPERENGLISH OPERATIONThe disk will continue to turn for some time after the engine has been shut off. Make sure disk has stopped
14 8 INCH TURNTABLE CHIPPEROPERATION4.6 RAISE/LOWER ACCESS COVER1. Rotate the discharge chute so it is parallel to the access cover.2. Remove the t
158 INCH TURNTABLE CHIPPERENGLISH OPERATIONFigure 4.2, Feed Roller Speed Control.4.8 CHIPPER FEED CONTROLLER4.9 FEED ROLLER CONTROL BARThis machine
IDENTIFICATION NUMBER LOCATIONYour machine will have either a serial number or vehicle identication number (VIN). VINs are located on the left side o
16 8 INCH TURNTABLE CHIPPEROPERATION4.10 TOWINGCE COMPLIANT MODELS:HOOKING1. Rotate the discharge tube to face the opposite direction of the towing
178 INCH TURNTABLE CHIPPERENGLISH Section5.1 MAINTENANCE SCHEDULESERVICE & MAINTENANCE5The items listed in this service and maintenance schedule
18 8 INCH TURNTABLE CHIPPERSERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYD
198 INCH TURNTABLE CHIPPERENGLISH SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE
20 8 INCH TURNTABLE CHIPPERSERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYD
218 INCH TURNTABLE CHIPPERENGLISH SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE
22 8 INCH TURNTABLE CHIPPERSERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYD
238 INCH TURNTABLE CHIPPERENGLISH SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE
24 8 INCH TURNTABLE CHIPPERSERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYD
258 INCH TURNTABLE CHIPPERENGLISH SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE
LIMITED WARRANTYThis warranty applies to all ECHO Bear Cat Outdoor Power Equipment manufactured by Crary Industries Inc.Crary Industries warrants to t
26 8 INCH TURNTABLE CHIPPERSectionTROUBLESHOOTING66.1 FLASH CODES FOR THE CONTROLLERGUIDE TO THE CONTROLLER FLASH CODES SIGNAL FREQUENCY CAUSE ACTION
278 INCH TURNTABLE CHIPPERENGLISH SPECIFICATIONSBefore performing any of the corrections in this troubleshooting chart, refer to the appropriate infor
28 8 INCH TURNTABLE CHIPPERTROUBLESHOOTINGMachine chips poorly.Dull chipper blades. Flip or sharpen blades.Drive belts loose or worn.Inspect drive b
298 INCH TURNTABLE CHIPPERENGLISH SectionSPECIFICATIONSCH8993HDESCRIPTION ENGLISH METRICOVERALL SIZE* 136" x 79" x 95" 345cm x 200cm x
30 8 INCH TURNTABLE CHIPPERSPECIFICATIONSBOLT TORQUESAE - 8SAE - 2ASAE - 5SAEGradeandHeadMarkingsBOLT DIAMETER10.94.8A8.8METRICGradeandHeadMarkingsBOL
318 INCH TURNTABLE CHIPPERENGLISH SectionOPTIONS8PART NUMBER DESCRIPTION14900-00 PINTLE HITCH31605-00 TACH/HOUR METER KIT74581-00 LOW PROFILE DISCHARG
Crary Industries Inc. is pleased to explain the evaporative emission control system (EECS) warranty on your 2013 equipment. New equipment must be desi
ECHO BEAR CATwww.bearcatproducts.com237 NW 12th Street, West Fargo, ND 58078-0849Phone: 701.282.5520 • Toll Free: 888.645.4520 • Fax: 701.282.9522E-ma
TABLE OF CONTENTSSAFETY ... 11.1 SAFETY ALERT SYMBOL ...
18 INCH TURNTABLE CHIPPERENGLISH Section1. Read and understand this owner’s manual. Be completely familiar with the controls and the pro
2 8 INCH TURNTABLE CHIPPERSAFETY1. The feed roller can cause serious injury or death. Keep hands, feet and clothing away from the feed roller and ch
38 INCH TURNTABLE CHIPPERENGLISH SAFETY1.6 MAINTENANCE & STORAGE SAFETY1.7 TOWING SAFETY1.8 BATTERY SAFETY1. Before inspecting, servicing,
4 8 INCH TURNTABLE CHIPPERSAFETYDO NOT OPERATE THIS EQUIPMENT IN THE VICINITY OF BYSTANDERS. DO NOT ALLOW CHILDREN TO OPERATE THIS EQUIPMENT. ALW
58 INCH TURNTABLE CHIPPERENGLISH SAFETY1.10 SAFETY DECAL LOCATIONS9758310**DECAL LOCATED NEXTTO VIN ON TURNTABLE41261213141511The numbers below corre
Comments to this Manuals