OWNER'S MANUAL8 INCH TURNTABLE CHIPPERCH8720iH - 720cc SUBARUPN: 31508-00Rev. 010113 Companion to 31514-00VIN Range: 5VJAA0000DW000001 - CurrentE
6 8 INCH TURNTABLE CHIPPERSectionASSEMBLY1. Mount tires and rims to the axle using the lug nuts.2. Attach the fender supports to the trailer using t
78 INCH TURNTABLE CHIPPERENGLISH ASSEMBLY2.3 REAR STABILIZERVerify that the rear stabilizer is installed. To install the rear stabilizer,
8 8 INCH TURNTABLE CHIPPERASSEMBLY2.6 ATTACH DISCHARGE TUBEKeep nuts as tight as possible while allowing the discharge tube to freely turn.NO
98 INCH TURNTABLE CHIPPERENGLISH ASSEMBLY2.9 ADD OIL TO ENGINE2.8 CHECK/ADD HYDRAULIC FLUID2.11 FILL THE FUEL TANK2.10 CONNECT THE BATTERYHydrauli
10 8 INCH TURNTABLE CHIPPERSectionFEATURES & CONTROLSUnderstanding how your machine works will help you achieve the best results when using your c
118 INCH TURNTABLE CHIPPERENGLISH FEATURES & CONTROLSThis controls the speed of the engine. Increase the throttle by moving the switch to the FAS
12 8 INCH TURNTABLE CHIPPERSectionOPERATIONAs with any other piece of outdoor power equipment, get-ting the feel for how your machine operates and get
138 INCH TURNTABLE CHIPPERENGLISH OPERATIONThe disk will continue to turn for some time after the engine has been shut off. Make sure disk has st
14 8 INCH TURNTABLE CHIPPEROPERATION4.6 RAISE/LOWER ACCESS COVER1. Rotate the discharge chute so it is parallel to the access cover.2. Remove the t
158 INCH TURNTABLE CHIPPERENGLISH OPERATIONFigure 4.2 - Feed Roller Speed Control.4.8 CHIPPER FEED CONTROLLER4.9 FEED ROLLER CONTROL BARNOTEThe disk
IDENTIFICATION NUMBER LOCATIONYour machine will have either a serial number or vehicle identication number (VIN). VINs are located on the left side o
16 8 INCH TURNTABLE CHIPPEROPERATION4.10 TOWINGCE COMPLIANT MODELS:HOOKING1. Rotate the discharge tube to face the opposite direction of the towing
178 INCH TURNTABLE CHIPPERENGLISH Section5.1 MAINTENANCE SCHEDULESERVICE & MAINTENANCE5SERVICE AND MAINTENANCE SCHEDULEFREQUENCYCOMPONENTMAINTENA
18 8 INCH TURNTABLE CHIPPERSERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYD
198 INCH TURNTABLE CHIPPERENGLISH SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE
20 8 INCH TURNTABLE CHIPPERSERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYD
218 INCH TURNTABLE CHIPPERENGLISH SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE
22 8 INCH TURNTABLE CHIPPERSERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYD
238 INCH TURNTABLE CHIPPERENGLISH SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE
24 8 INCH TURNTABLE CHIPPERSERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE THE HYD
258 INCH TURNTABLE CHIPPERENGLISH SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, DISENGAGE
LIMITED WARRANTYThis warranty applies to all ECHO Bear Cat Outdoor Power Equipment manufactured by Crary Industries Inc.Crary Industries warrants to t
26 8 INCH TURNTABLE CHIPPERSectionTROUBLESHOOTING66.1 FLASH CODES FOR THE CONTROLLERGUIDE TO THE CONTROLLER FLASH CODES SIGNAL FREQUENCY CAUSE ACTION
278 INCH TURNTABLE CHIPPERENGLISH SPECIFICATIONSBefore performing any of the corrections in this troubleshooting chart, refer to the appropriate infor
28 8 INCH TURNTABLE CHIPPERTROUBLESHOOTINGMachine chips poorly.Dull chipper blades. Flip or sharpen blades.Drive belts loose or worn.Inspect drive b
298 INCH TURNTABLE CHIPPERENGLISH SectionSPECIFICATIONSCH8720iHDESCRIPTION ENGLISH METRICOVERALL SIZE 136" x 79" x 95" 345cm x 200cm x
30 8 INCH TURNTABLE CHIPPERSPECIFICATIONSBOLT TORQUESAE - 8SAE - 2ASAE - 5SAEGradeandHeadMarkingsBOLT DIAMETER10.94.8A8.8METRICGradeandHeadMarkingsBOL
318 INCH TURNTABLE CHIPPERENGLISH SectionOPTIONS8PART NUMBER DESCRIPTION14900-00 PINTLE HITCH31605-00 TACH/HOUR METER KIT74581-00 LOW PROFILE DISCHARG
Crary Industries Inc. is pleased to explain the evaporative emission control system (EECS) warranty on your 2013 equipment. New equipment must be desi
ECHO BEAR CATwww.bearcatproducts.com237 NW 12th Street, West Fargo, ND 58078-0849Phone: 701.282.5520 • Toll Free: 888.645.4520 • Fax: 701.282.9522E-ma
TABLE OF CONTENTSSAFETY ... 11.1 SAFETY ALERT SYMBOL ...
18 INCH TURNTABLE CHIPPERENGLISH SectionUnder California Law and the laws of several other states, you are not permitted to operate an inter
2 8 INCH TURNTABLE CHIPPERSAFETYhave come to a complete stop before inspecting or servicing any part of the machine. Disconnect the bat
38 INCH TURNTABLE CHIPPERENGLISH SAFETY1.6 MAINTENANCE AND STORAGE SAFETY1.7 TOWING SAFETY1.8 BATTERY SAFETY1. Before inspecting, servicing, st
4 8 INCH TURNTABLE CHIPPERSAFETY1.9 SAFETY DECALSKEEP HANDS AND FEET OUT OF INLET AND DISCHARGE OPENINGS WHILE MACHINE IS OPERATING TO AVOID SERIOUS
58 INCH TURNTABLE CHIPPERENGLISH SAFETY1.10 SAFETY DECAL LOCATIONS4126538791011*12131415The numbers below correspond to the decals in Section 1.9. F
Comments to this Manuals