OWNER'S MANUAL5 INCH CHIPPERCH5540H - 540 PTO HYDRAULIC FEEDPN: 12666 Rev. 010113 Companion to 12665SN Range: D00001 to Current ENGLISH
65 INCH CHIPPERASSEMBLY2.2 ATTACH DISCHARGE TUBEKeep nuts as tight as possible while allowing the discharge tube to freely turn.NOTE1. Attach one cl
7 5 INCH CHIPPERENGLISH ASSEMBLY2.3 CONNECT PTO DRIVELINEThe driveline supplied with this machine may need to be cut to a shorter length for proper o
85 INCH CHIPPERSection1. Belt Guard: Remove to grease rotor and jack shafts and to check or replace belt.2. Discharge Lock: Used to pivot and lock t
9 5 INCH CHIPPERENGLISH Section1. Read and understand all safety warnings and chipping guidelines contained in this manual before proceeding.2. Conn
105 INCH CHIPPEROPERATIONTo prevent personal injury or property damage: shut off engine and make sure that all moving parts have come to a complete st
11 5 INCH CHIPPERENGLISH SectionSERVICE & MAINTENANCEWARNING55.2 SERVICE & MAINTENANCE SCHEDULESERVICE AND MAINTENANCE SCHEDULEFREQUENCYCOMPO
125 INCH CHIPPERSERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, AND MAKE SURE ALL MOVING PAR
13 5 INCH CHIPPERENGLISH SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, AND MAKE SURE ALL M
145 INCH CHIPPERSERVICE & MAINTENANCEFigure 5.5 Belt and pulleys with belt shield removedIDLER PULLEYROTOR SHAFTLubricate the machine periodical
15 5 INCH CHIPPERENGLISH SERVICE & MAINTENANCEBEFORE INSPECTING OR SERVICING ANY PART OF THIS MACHINE, SHUT OFF POWER SOURCE, AND MAKE SURE ALL M
Before You BeginDEAR ECHO BEAR CAT CUSTOMERThank you for purchasing a ECHO Bear Cat product. The ECHO Bear Cat line is designed, tested, and manufact
165 INCH CHIPPERSERVICE & MAINTENANCECAUTIONHandle pressurized hydraulic uid carefully. Escaping pressurized hydraulic uid can have sufcient fo
17 5 INCH CHIPPERENGLISH Section6 TROUBLESHOOTING6.1 FLASH CODES FOR CONTROL LIGHTGUIDE TO THE CONTROLLER FLASH CODES SIGNAL FREQUENCY CAUSE ACTION T
185 INCH CHIPPERTROUBLESHOOTINGPROBLEM POSSIBLE CAUSES REMEDYController light ashes green.Chipper disk RPM not high enough to chip.Increase throttle
19 5 INCH CHIPPERENGLISH TROUBLESHOOTING Cannot engage belt.Improper belt installation; belt not under belt guide.Install belt properly; install belt
205 INCH CHIPPERSectionSPECIFICATIONS7 CH5540HDESCRIPTION ENGLISH METRICOVERALL SIZE 49" x 68" x 90"124cm x 172,7cm x 228,6cm OVERALL W
21 5 INCH CHIPPERENGLISH SPECIFICATIONSBOLT TORQUEBOLT DIAMETER (A)METRICBOLT TORQUE *4.8 8.8 10.9 12.9N.m Ft-lb. N.m Ft-lb. N.m Ft-lb. N.m Ft-lb.M3 0
225 INCH CHIPPERSectionOPTIONS8 Part # DECSCRIPTION72493 CHIPPER BLADE KIT73071 AUTO FEED KITAUTO FEED KIT, 73071CHIPPER BLADE KIT, 72493
ECHO BEAR CATwww.bearcatproducts.com237 NW 12th Street, West Fargo, ND 58078-0849Phone: 701.282.5520 • Toll Free: 888.645.4520 • Fax: 701.282.9522E-ma
ENGLISHLIMITED WARRANTYThis warranty applies to all ECHO Bear Cat Outdoor Power Equipment manufactured by Crary Industries Inc.Crary Industries warran
iv5 INCH CHIPPERSAFETY ...11.1 SAFETY AL
1 5 INCH CHIPPERENGLISH Section1SAFETYThe Owner/Operator's manual uses this symbol to alert you of potential hazards. Whenever you see this symb
25 INCH CHIPPERSAFETY1.3 OPERATION SAFETY1.5 MAINTENANCE AND STORAGE1.6 PTO SAFETY1.4 FEED ROLLER SAFETY1. Always stand clear of discharge area w
3 5 INCH CHIPPERENGLISH OPERATION1.6 PTO SAFETY (CONT.)1.7 SAFETY DECAL LOCATIONSSee Section 1.8 for decal descriptions. Familiarize yourself with
45 INCH CHIPPERSAFETYSee Section 1.7 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine and the ass
5 5 INCH CHIPPERENGLISH Section2ASSEMBLY1. Mount the feed chute to the chipper housing using six 3/8 x 1-1/4" carriage bolts, 3/8" washers,
Comments to this Manuals