Echo 99944230001 User Manual download pdf

i n s t a l l a t i o n

1. Loosen two (2) screws (A) and remove center locating screw (B).

Pull gear case assembly from drive shaft housing.

2. Set power head / driveshaft so that power head rests on tank stand.

3. Slide new gear case onto drive shaft housing so that gear case rests

upright on wheel.

IMPORTANT

Flat edge of washers (D) must be against drive shaft.

4. Tighten bolts (F), clamping the cutting attachment onto the

housing.

5. Install self-tapping screw into locating hole (E) in gear case.

IMPORTANT

Assure gear case wheel and engine remain properly aligned while

installing self-tapping locating screw.

NOTE

After converting your SRM to a Power Edger, access www.echo-

usa.com or call ECHO at 1-800-673-1558 to get the appropriate

Power Edger operator’s manual.

X7672230500

X767000220

01/10

PE Pr o to r q u E GE a r Ca s E

C C E s s o r y Kit

n s t a l l a t i o n in s t r u C t i o n s

P/N 99944230001

b l a d E r E P l a C E m E n t

Level 1.

Tools Required: T-wrench, Locking Tool, Needle Nose Pliers,

13 mm Open End Wrench

Parts Required: POWER BLENDX

8 oz. (P/N 91014) or

Lithium Base Grease, Blade P/N 69601552632,

split pin P/N 90030020022

NOTE

Grease gear case every 15 - 25 hours of use. Replace blade when

it is worn shorter than 6 inches. Remove blade and adapters before

greasing to prevent damage to gear and bearings.

1. Shut engine off. Disconnect spark plug lead from spark plug.

Tools Required: 5/16 in. Wrench

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - P/N 99944230001

i n s t a l l a t i o n1. Loosen two (2) screws (A) and remove center locating screw (B). Pull gear case assembly from drive shaft housing.2. Se

Page 2

22. Remove split pin (A).3. Rotate blade until holes in inner blade adapter (B) and gear box align. Insert locking tool to lock PTO shaft (C).NOTE

Page 3 - d E l a h o j a

r E E m P l a z o d E l a h o j aNivel 1.Herramientas necesarias: Combinación de destornillador y llave, herramienta de traba, alicates

Page 4

4ABCDEF2. Quite el pasador hendido (A).3. Gire la hoja hasta que se alineen los agujeros del adaptador interior de la hoja (B) y la caja de engranaj

Page 5 - 99944230001

i n s t a l l a t i o n1. Desserrer les deux vis (A) et retirer la vis de centrage (B). Retirer le boîtier de transmission du carter de l’arbre d’

Page 6

62. Retirer la goupille fendue (A).3. Faire tourner la lame à la main jusqu’à ce que les trous de son adaptateur interne (B) s’alignent sur ceux de

Page 7 - REMARQUES

NOTESNOTASREMARQUES

Page 8 - LAKE ZURICH, IL 60047 U.S.A

ECHO, INCORPORATED400 OAKWOOD ROADLAKE ZURICH, IL 60047 U.S.A.www.echo-usa.comECHO CONSUMER PRODUCT SUPPORT: If you require assistance or have questio

Comments to this Manuals

No comments

Echo 99944230001 User Manual

Browse online or download User Manual for Unknown Echo 99944230001. Echo 99944230001 User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Echo 99944230001