Echo HC-2410 User Manual

Hedge ClipperOperator's ManualMODELS:HC-1500 Serial Number 001001 - 999999HC-1500 - Type 2E Serial Number 001001 - 672900HC-1600 Serial Number 00

10141812158616115717HC-2000, 2400, 241021HC-1500, 16003467891011121314151610131920

HEDGE CLIPPEROPERATOR'S MANUAL111. OPERATOR'S MANUAL - Read and understand this manual before operation. Keep manual in a safelocation for

12SPECIFICATIONSLEDOME10051-CHE20051-CHE10061-CHE10002-CHE10042-CHE20042-CHE10142-CHE20142-CHhtgneLmm069).ni8.73(mm3311).ni6.44(mm099).ni0.93(mm0301).

HEDGE CLIPPEROPERATOR'S MANUAL13ASSEMBLY HC MODELS ARE PRE-ASSEMBLED IN THE BOX.Tools Required: NoneParts Required: NonePRE-OPERATIONFUELFuel R

14Handling FuelWARNING DANGERFuel is VERY flammable. Use extreme care when mixing, storing orhandling or serious personal injury may result.•

HEDGE CLIPPEROPERATOR'S MANUAL15EQUIPMENT CHECKBefore operation a complete check of the unit must be performed;• Check unit for loose/missing nu

164.5 m (15 ft.)CBCOLDSTARTRUNIDLEH LOPERATION• Provide all users of this equipment with the Operator's Manual andinstructions for Safe Operat

HEDGE CLIPPEROPERATOR'S MANUAL174. START - PULL ROPELay the hedge clipper on a flat clear area and pull the recoil starterhandle (D) until engine

18STOPPING ENGINE1. RELEASE THROTTLE. Allow engine to idle for a minute.2. STOP SWITCH - STOP. Move stop switch (A) to STOP position.WARNING

HEDGE CLIPPEROPERATOR'S MANUAL19MAINTENANCE INTERVALSmetsyS/tnenopmoCecnanetniaMerudecorPerofeBesUyrevEleufeRyliaDroyrevE4sruoH3shtnoM001rosruoH6

20AIR FILTERLevel 1.Tools required: 25 or 50 mm (1 or 2 in.) medium bristle paint brushParts required: 90008 REPOWERTM AIR & FUEL FILTER KIT1. Cl

HEDGE CLIPPEROPERATOR'S MANUAL21SPARK PLUGLevel 2.Tools required: T-wrench, Feeler gauge, Soft metal brushParts required: 90064 REPOWERTM Tune-Up

221. Remove starter and disconnect the throttle cable end from thecarburetor.2. Remove the two screws that retain the engine cover. Lift the engineco

HEDGE CLIPPEROPERATOR'S MANUAL231. Before adjusting the carburetor, clean or replace the air filter andspark arrester screen.2. Start engine and

24Basic Setting1. Stop engine and turn both LO (B) and HI (A) needles in, CW untilthey stop and are lightly seated.IMPORTANTDO NOT over tighten needle

HEDGE CLIPPEROPERATOR'S MANUAL25LUBRICATIONBladesLevel 1.Tools required: Clean rag, 25 or 50 mm (1 or 2 in.) medium bristle paintbrushParts Requi

26Gear Box AssemblyLevel 2.Tools required: 3 mm Hexagon wrench, Grease GunParts Required: Gear Box Gasket, HC-2400 P/N 61041401260,HC-1500 2E P/N 6104

HEDGE CLIPPEROPERATOR'S MANUAL27HC-1500, Type 2E, HC-2400, 2410 (All)Level 1.Tools required: Grease Gun, Clean ragParts required: ECHO® LUBETM 8

28SHARPENING BLADESLevel 3.Tools required: Flat file, ScrewdriverParts required: NoneWARNING DANGERHedge Clipper Blades are very sharp. We

HEDGE CLIPPEROPERATOR'S MANUAL29WARNING DANGERFuel vapors are extremely flammable and may cause fire and/or explosion. Never test for ig

HEDGE CLIPPEROPERATOR'S MANUAL3Throughout this manual and on the product itself, you will find safetyalerts and helpful, information messages pre

30STORAGELong Term Storage (over 30 days)Do not store your unit for a prolonged period of time (30 days or longer)without performing protective storag

HEDGE CLIPPEROPERATOR'S MANUAL31NOTES

ECHO, INCORPORATED400 OAKWOOD R OADLAKE ZURICH, IL 60047-1564www.echo-usa.comDEALER?Call1-800-432-ECHO1-800-432-3246www.echo-usa.comCONSUMER PRODUCTS

9992220353201/02SUP22203532SUPPLEMENT TO OPERATOR'S MANUALPART NUMBER X7532248103 (89861105635)FOR MODEL: HC-1500, -1600, -2000, -2400, -2410SUPL

2CONTENTS__ 1 - Hedge Clipper Assembly__ 1 - Operators Manual__ 1 - Safety Manual__ 1 - Warranty Statement__ 1 - Warranty Registration Card__ 1 - Plas

4Symboldescription/applicationSymbol form/shapeSymboldescription/applicationSymbol form/shapeHotSurfaceCarburetor adjustment- Idle speedCarburetor adj

HEDGE CLIPPEROPERATOR'S MANUAL5FUELWARNING DANGERFuel is VERY flammable. Use extreme care when mixing, storing orhandling or serious per

6Physical Condition --Eye Protection --Eye protection that meet ANSI Z87.1 or CE requirements must be wornwhenever you operate the Hedge Clipper.Hand

HEDGE CLIPPEROPERATOR'S MANUAL7SAFE OPERATIONDetermine Operation Area• Do not operate this product indoors or in inadequately ventilatedareas.• R

8EXTENDED OPERATION/EXTREME CONDITIONSVibration and ColdIt is believed that a condition called Raynaud’s Phenomenon, whichaffects the fingers of certa

HEDGE CLIPPEROPERATOR'S MANUAL9DESCRIPTIONThe ECHO product you purchased has been factorypre-assembled for your convenience.After opening the car